Home > Spray Foam Materials > Closed Cell > Premium/ Accella > Foamsulate 220

Foamsulate 220

Foamsulate 220 is a two-component, medium density, one to one by volume spray applied polyurethane foam. To produce Foamsulate 220 requires the use of an “A” component (ISO) and a blended “B” component (RESIN) which contains ZERO ozone depleting blowing agents, catalysts, polyols and fire retarding materials. Foamsulate 220 is an insulation system designed for use in residential, commercial and industrial applications. Use in lieu of more traditional forms of insulating materials such as fiberglass, cellulose or other loose fill products.

Typical area’s where spray polyurethane foam is applied are:

EXTERIOR WALLS, VENTED ATTICS, UN-VENTED ATTIC ASSEMBLIES, BETWEEN FLOORS, FOUNDATIONS CRAWLSPACES, HVAC DUCTS, FLUID TANKS, COLD STORAGE UNITS

Foamsulate™ 220 is a 2.0 LB density closed cell insulating material. Foamsulate™ 220 is designed for use where insulation systems require superior air barrier characteristics along with the ability to minimize moisture infiltration. Foamsulate™ 220 has a high R-value rating while providing structural enhancement due to its rigid nature when cured. When properly installed by a trained contractor Foamsulate™ 220 quickly expands to fill the cracks, crevices, gaps and voids that exist in every structure. In addition Foamsulate™ 220 will conform to the curves, irregular surfaces and spaces to form a superior thermal envelope around your entire structure.

Category:
Downloadable PDF's

Español

More Closed Cell Foams

Specification

Property FOAMSULATE 220 TEST
R-VALUE 7.0 @ 1″ ASTM C 518
CORE DENSITY 2.0 LB / Cubic Foot ASTM D 1622
CLOSED CELL CONTENT > 96% ASTM D 6226
SOUND TRANSMISSION COEFFECIENT 38 ASTM E 413
WATER VAPOR TRANSMISSION –
PERMEANCE		 1.49 Perms at 1”
0.92 Perms at 1.5”
0.77 Perms at 2”		 ASTM E 96
AIR IMPERMEABLE < 0.005 (L/s-m2) ASTM E 283
NOISE REDUCTION COEFFICIENT 0.10 ASTM C 423
TENSILE STRENGTH (PSI) 58 ASTM D 1623
DIMENSIONAL STABILITY < .27% ASTM D 2126
COMPRESSIVE STRENGTH (PSI) 41 ASTM D 1621

BUILDING CODE CERTIFICATIONS / FIRE TEST DATA
EVALUATION SERVICE REPORT IAPMO 352
BUILDING TYPES Approved I, II, III, IV, V-B: Nonstructural Insulating Material
FLAME SPREAD ASTM E84 Class I < 10
SMOKE DEVELOPMENT ASTM E84 Class I < 195
ASTM C 1029 Spray Applied Polyurethane Thermal Insulation Meets or Exceeds Type II
ASTM E 119 Pass Non Load-Bearing – 1 Hour Rated – Wall Assembly
NFPA 259 Potential Heat 1883 Btu/ft2 Per Inch Of Thickness
NFPA 285 Pass Compliant For Use In Building Types: I, II, III, IV, V
UL LISTING FWFX.R38039 Exterior Wall System Components
UL LISTING FWFO.EWS0013 System No. EWS0013 Exterior Wall Systems
UL GREENGUARD GOLD GOLD: UL 2818 – 2013 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings.
NFPA 286 Pass: Can be used without a code prescribed 15-minute thermal barrier when covered with one of the approved intumescent coatings as shown on page 2.
NFPA 286
AC377 APPENDIX X		 Pass: Complies with the applicable requirements of ICC-ES AC377 Appendix X for use in attics and crawlspaces without a prescriptive ignition barrier.
UL 1715 Pass: Can be used without a Code prescribed 15-minute thermal barrier when included as a component in tested alternative thermal barrier assemblies.
FLORIDA BUILDING CODE FL 17185: FL Building Code 2010: RULE 61G20-3: Approved for use as supplemental attachment of roof OSB deck to rafters/truss top chords (dimensional lumber) for commercial and residential buildings. Product may be used for Code-plus wind resistance in new construction or enhancing the wind uplift resistance on existing structures.